Attention Hiring Manager:

Are you looking for a results-oriented leader seeking a challenging

opportunity? An experienced technical professional to offer my over 10

years experience in construction, electrical, oil and gas and technical

fields? Then I am the right candidate for your organization.

The position matches well with my experience, education and career

objective. I am familiar with the description of the job and feel my skills and

hands on experience within the technical industries I have worked are a

good match and valuable assets I can bring to your organization.

My unique combination of skills and education has enabled me to interact

well with a diverse population and a team oriented environment within large

and small organizations. I am seeking a position where I can utilize my vast

experience while continuing to grow professionally.

Since the enclosed resume is only a brief summary of my experience and

capabilities, I would welcome the opportunity to meet with you to discuss

how I could put my energy and drive to work for your organization. I look

forward to the opportunity of further discussing the position with you in

person. Thank you for your time and consideration.

Work Experience

Manager: Level II MT/PT Inspector

PROFESSIONAL NDT SERVICES

-

Cleburne, TX

September 2011 to Present

Non-destructive testing (NDT) is a wide group of analysis techniques used in science and industry to

evaluate the properties of a material, component or system without causing damage.

• Provide insurance and safety for those working out in the oilfield.

• Conduct various testing's such as magnetic particle and dye penetrant.

• Clean all tools by buffing them and scrubbing all outer and inside diameters of each piece

• Conduct a series of testing depending on either the customers Standard Operating Procedures or that of

Professional NDT's.

• Determines whether to blacklight M/T or use dye penetrant P/T.

• Check each individual piece for cracks, fatigue, washing, scarring and any damage that can be

potentially fatal or stop progress in the field.

• All work performed is from the DS-1.

Once completed all work is written up for each piece examined and is determined to be a failure or

runnable according to the specifications.

• Use of calipers: OD/ID: Dial calipers, XT calipers: Engineer scale: Dummy stick: Grinders 4" and 6":

White light meter, UV meter, gauss meter, DC coil, AC coil, Variat coil, UV blacklight and a Yoke,

micrometers(minimal).

Electrician Apprentice

TEXSUN ELECTRIC

-

Fort Worth, TX

October 2010 to July 2011

Industrial - Underground work, duct bank, dig trenches, PVC, rigid conduit, pull wire, terminate, install

buss duct, switchgear and busses, and apprentice duties.

• Read blue prints for interpreting where each piece of pipe, switchgear etc.

• Lay according to scale

Owner/Operator

Green Blade Lawn Care Services

-

Burleson, TX

January 2008 to April 2010

Mow, edge, blow, fertilize,

• Yard clean-up, plant flowers, trees, clean gutters, cut shrubs

• Ensure each customer was satisfied with the way there yards results for customer satisfaction.

Electrician Apprentice

LIGHTNING ELECTRIC

-

Burleson, TX

January 2007 to December 2007

Service work - Wire and Install fans, lights, plugs, switches

• Dig trenches for laying underground pvc and wire

Wireman Level 2

QUALITY SIGNAL CONSTRUCTION

-

Fort Worth, TX

November 2006 to December 2006

Wire railroad houses

• install bus bars

• data analyzers

• recorders, relays

• crossing lamp controllers

• terminal blocks

• Put up gates, lights and mechanisms

Electrician Apprentice

LIGHTNING ELECTRIC

-

Burleson, TX

February 2006 to November 2006

Service work - Wire and Install fans, lights, plugs, switches

• Dig various trenches for wire and pvc

• Climb attics, ladders, use various power tools

Wireman Level 2

QUALITY SIGNAL CONSTRUCTION

-

Fort Worth, TX

November 2005 to February 2006

Wire railroad houses, install bus bars, data analyzers, recorders, relays, crossing lamp controllers,

terminal blocks.

• Put up gates, lights and mechanisms.

• Utilize various blue prints to conduct where each relay, switch, recorders were to be placed inside the

bungalows.

• Drive forklifts for moving the bungalows inside and outside warehouse as well as installing them on

trailers.

Tower Hand

BIC ENTERPRISES

-

Burleson, TX

March 2005 to November 2005

Climb towers changing light bulbs, removing and installing transmission lines, and antenna's

Electrician Apprentice

METRO-TEX ELECTRIC

-

Joshua, TX

December 2004 to February 2005

Trim out custom homes, plugs, switches, lights, doorbells, exhaust fans ceiling fans and outdoor lighting

Electrician Apprentice

JW ELECTRIC

-

Arlington, TX

June 2004 to November 2004

Provide helper duties to the foreman, run EMT, MC for lighting, switches. Plugs.

• Service and warranty work - houses, remodels, lease spaces and banks.

• Read and interpret blue prints.

Electrician Apprentice

CABLE ELECTRIC

-

Richland Hills, TX

October 2003 to June 2004

Wire and install lights, plugs, switches, run PVC for underground new construction, EMT. Lease spaces,

banks, schools.

• Learn to use blue prints.

Education

Certificate

Texas State Technical College -

Breckenridge, TX

November 2002 to April 2003

Diploma

Burleson High School -

Burleson, TX

2001

Certifications

Magnetic Particle Level II QC-001

May 2012 to May 2017

Magnetic Particle inspection is a process of non destructive testing. Magnetic particle Inspection (MPI) is

a non-destructive testing (NDT) process for detecting surface and slightly subsurface discontinuities in

ferromagnetic materials such as iron, nickel, cobalt, and some of their alloys.

Liquid Penetrant Level II QC-001

June 2012 to June 2017

Liquid Penetrant is a form of non destructive testing .Dye penetrant inspection (DPI), also called liquid

penetrant inspection (LPI) or penetrant testing (PT), is a widely applied and low-cost inspection method

used to locate surface-breaking defects in all non-porous materials (metals, plastics, or ceramics).

RigPass

May 2012 to Present

This is a certification that covers offshore and onshore safety and guidelines. IADC's Rig Pass® program

is an accreditation system delivering a standardized safety orientation program for new employees,

preparing the employees for almost any operating environment, at almost any site, onshore or offshore.

Completion of an IADC Rig Pass® accredited program confirms that personnel have met basic

requirements defined by safety and training professionals in the drilling industry, irrespective of the rig's

location.

OSHA refresher with Hazwoper Level 1

June 2014 to June 2015

OSHA refresher course covers, Compliance Solutions NEW interactive web-based, 8-Hour HAZWOPER

Annual Refresher provides a convenient way for employees who have completed initial 24 or 40-Hour

HAZWOPER training to meet OSHA mandated refresher requirements under 29 CFR 1910.120. These

are some of the courses learned: Site Emergencies

Information Sources

Personal Protective Equipment

Respiratory Protection

Hazard Communications

Toxicology

Radiation Safety

Medical Surveillance

Air Monitoring

Fire Protection

Sampling

Decontamination

Containment of Hazardous Material Spills

First Aid in the Workplace/CPR

March 2015 to March 2016

The Occupational Safety and Health Administration (OSHA) has certain requirements regarding first aid

and CPR preparedness in the workplace. Some OSHA compliance standards require specific types of

industry to provide first-aid and CPR training to employees.